x X X X X 533 NO SLIP COMBO SPROCKETS REQUIRES A FULLY CLIPPED TRACK THAT HAS ALL WINDOWS OPEN Drives against involute lugs and open windows SPROCKET DIAMETER (WITHOUT KNOBS) 2.52” 7 Tooth 5.48” 8 Tooth 6.26” 9 Tooth 7.05” 10 Tooth 7.83” 2.86” 7 Tooth 6.24” 8 Tooth 7.13” 3.0” 7 Tooth 6.55” 8 Tooth 7.49” # Due to the press fit required, UHMW sprockets commonly measure as much as 1/8” less than the desired shaft size. ** Sleeve Tool required to install No Slip Sprockets on Ski-Doo splined shafts Note: Some models will require that the front of the slide rails be shortened for clearance. We recommend that the skid frame be installed without the springs and cycled to check rail tip to sprocket clearance. If rails must be shortened, Anti-stab kit must be installed (see page 365) Model Shaft Dia. 1 1/2” Track Height 2” Track Height 2 1/4” Track Height ARCTIC CAT AWS I & II (aluminum spindle housings) 1-1/16” 8 tooth sprockets required 7 tooth sprockets required 7 tooth sprockets with track trimmed AWS III IV & V (steel spindle housings) except `00-03 Powder Special / Mtn Cat 1-1/16” 9 tooth stock sprockets 8 tooth or 9 tooth with notched track 8 tooth sprockets with track trimmed `00-02 Powder Special / Mtn Cat (rolled chaincase stock) 1-1/16” 9 tooth stock sprockets 9 tooth stock sprockets 9 tooth sprockets with track trimmed POLARIS `80-96 models except below 1” 8 tooth sprockets required 7 tooth sprockets required 7 tooth sprockets with track trimmed `95-96 XLT XCR600 Storm; `96 Ultra; `97-02 all models except RMK 1” 9 tooth stock sprockets 8 tooth sprockets required 8 tooth sprockets with track trimmed `97-01 RMK (rolled chaincase stock) 1” 9 tooth stock sprockets 9 tooth stock sprockets 9 tooth sprockets with track trimmed SKI-DOO `85-94 PRS & DSA models (dual rear shocks) 1-1/4” 8 tooth sprockets required 7 tooth sprockets required Rolled chaincase required `95-02 S-2000 & CK3 models 1-1/4” 9 tooth stock sprockets 8 tooth sprockets required 8 tooth sprockets with track trimmed `99-03 ZX models 1-1/16” 9 tooth stock sprockets 9 tooth stock sprockets 9 tooth sprockets with track trimmed YAMAHA `92-97 V-Max 4 27mm (1-1/16”) 8 tooth sprockets required 7 tooth sprockets required 7 tooth sprockets with track trimmed `94 V-Max 500 & 600 27mm (1-1/16”) 7 tooth or 8 tooth with cooler removed 7 tooth sprockets with cooler removed 7 tooth cooler removed and track trimmed `95-96 V-Max / Mtn Max 500 & 600 High profile tracks will not fit XT 27mm (1-1/16”) 8 tooth sprockets required 7 tooth sprockets required 7 tooth sprockets with track trimmed `97-03 V-Max `97-99 Mtn Max High profile tracks will not fit XT 27mm (1-1/16”) 9 tooth stock sprockets 8 tooth sprockets required 8 tooth sprockets with track trimmed `00-03 Mtn. Max 27mm (1-1/16”) 9 tooth stock sprockets 9 tooth stock sprockets 9 tooth stock sprockets SPROCKET SIZE CHART for OLDER MODELS (2.52” PITCH) • Addresses bulkhead clearance when installing taller height tracks. 54-2510 54-2511 54-2512 54-2533 Shaft Size# Pitch 7 Tooth List 8 Tooth List 9 Tooth List 10 Tooth List HEX SHAFTS 25mm & 1” 2.52” 54-2509 $111.95 54-2510 $111.95 2.86” 54-2530 $119.95 1-1/16”, 27mm, 1-1/8” 2.52” 54-2508 $111.95 54-2513 $111.95 54-2514 $119.95 54-2515 $122.95 2.86” 54-2533 $119.95 54-2534 $122.95 3.0” 54-2523 $118.95 54-2524 $122.95 1-1/4” 2.52” 54-2507 $111.95 2.86” 54-2536 $119.95 54-2537 $122.95 3.0” 54-2527 $122.95 POLARIS SPLINED SHAFTS (IQ AND PRO CHASSIS - EXCEPT BELT DRIVE MODELS) 2.86” 54-2541 $129.95 SKI-DOO SPLINED SHAFTS 3.0” 54-2553 ** $129.95 SNOW BIKE SURVIVAL SNOWMOBILE ACCESSORIES HANDLEBARS / CONTROLS CABLES WINDSHIELDS BODY SKIS / RUNNERS FRONT SUSPENSION REAR SUSPENSION SHOCKS TRACKS / STUDS SPROCKETS ELECTRICAL EXHAUST ENGINE AIR / FUEL CLUTCHING BELTS BRAKES CHAIN / SPROCKETS LUBRICANTS / CHEMICALS TOOLS / HARDWARE TRANSPORT / RAMPS INDEX TRACKS / STUDS / SPROCKETS
RkJQdWJsaXNoZXIy OTUwNDk=